We recommend you use a tripod when taking landscape pictures. The shutter speed indicator still blinks if you use a tripod, but camera shake will not be a problem. Page Sports Mode Sports Mode If the shutter speed indicator blinks, the shutter speed may be too slow to keep the picture from being blurred by camera shake.
Be careful to hold the camera steady and press the shutter button smoothly, or use a tripod. Page Advanced Operations Advanced Operations Creative zone The Creative zone features shooting modes that let you select the shutter speed or aperture value and change the exposure yourself, providing you with more flexibility to set up the camera for a variety of shooting styles. This chapter describes how to make effective use of each of these functions.
Page Iso Speed Conversely, lower speeds are less suited to moving subjects or dim conditions, but produce sharper, more detailed images. The default setting is ISO Page Setting Processing Parameters Setting Processing Parameters Contents of processing for the captured image parameters: [contrast], [sharpness],[saturation] and [color tone] can be set with the camera, and you can set and register up to three sets of parameters.
Parameter Setting Adjusts the If this happens, you will not be able to take a picture even if you press the shutter button down fully. Instead, reframe the shot and focus again.
Automatic selection : The camera selects the AF point automatically according to conditions. This technique is called Focus Lock. The Basic Zone uses evaluative metering.
In the Creative zone, any of the three modes can be selected. The viewfinder field is divided into 35 metering zones to which the three AF points are linked for evaluative metering. In the Basic Zone the Auto setting is selected automatically, while in the Creative zone you can select any of the seven white balance settings. Page White Balance Settings White Balance Settings In light from any source, the proportion of the primary colors red, green, blue in the light varies according to the color temperature.
Higher color temperatures contain a greater proportion of blue, and lower color temperatures contain a greater proportion of red. Partial metering zone Photograph a white subject. Page Shutter-Priority Ae Shutter-Priority AE In this mode, you set the shutter speed, and the camera automatically sets the aperture value to suit the brightness of the subject.
This is called Shutter-Priority AE. A fast shutter speed can freeze the motion of a fast-moving subject, and a slow shutter speed can blur the subject to give the impression of motion. Page 71 Shutter Speed Display You can set the shutter speed in half-stop increments as shown below. Page Aperture-Priority Ae Aperture-Priority AE In this mode, you set the aperture value, and the camera automatically sets the shutter speed to suit the brightness of the scene. This is called Aperture-Priority AE.
By setting a smaller aperture value larger aperture , you can blur the background to make the subject stand out as in a portrait. The higher the aperture value, the smaller the aperture opening. The range of aperture settings displayed depends on the lens mounted on the camera. Page Manual Exposure Manual Exposure In this mode you set the shutter speed and aperture value yourself.
The camera makes no settings automatically. You can determine the correct combination of shutter speed and aperture value by checking the exposure level displayed in the camera. All the subjects covered by the AF points, from those close to the camera to those far away from the camera, can be taken clearly. Fn and then use AEB, single-frame shooting takes effect even if the drive mode is set to continuous shooting.
After locking the exposure, you can recompose the shot while maintaining the exposure level. This feature is useful for backlit and spotlighted subjects. You can use it in any Basic mode or Creative mode. We recommend using a tripod when you use the self-timer. Do not stand in front of the camera when you press the shutter button to start the self-timer. Page Using The Eyepiece Cover Self-timer Operation Using the Eyepiece Cover If you take a picture using the self-timer or remote switch optional without looking through the viewfinder, stray light can enter the eyepiece and affect the exposure.
To prevent this, attach the eyepiece cover to the viewfinder eyepiece before taking the picture. Remove the eyecup. Page Bulb Exposures Bulb Exposures In a bulb exposure, the shutter remains open as long as you hold the shutter button down, and closes when you release it. Bulb exposures are useful for the long exposures required for night scenes, fireworks, etc.
The elapsed exposure time displayed on the LCD panel is only counted up to seconds. This function raises the mirror and exposes the picture, in separate operations. It is useful for close-up shots or when using a super telephoto lens, where the mirror shock could affect the picture. The procedure is as easy as a normal AE shot. Otherwise the lens barrel may partially obstruct the flash and cause part of the photo to look dark.
FE Lock is a function in the Creative zone. You cannot use flash exposure compensation in the Basic Zone. Regarding the operation of the EX, refer to the Speedlite's instructions.
FE lock works in both the normal flash and high-speed sync FP flash modes. You can view these images in single-image format, index format, or enlarged format. Viewing a Single Image Viewing the Index This mode displays 9 images simultaneously on a single screen.
Jump bar Image 10 Current Image 10 frames back image frames forward Viewing Recorded Images Select the image you want to enlarge from a single-image or index display. Page Info. Image information is available only for single-image displays. Each image is displayed for approximately 3 seconds. This allows you to play images with the correct orientation. To erase a protected image, you must first remove the protection. This section describes how to erase all the images recorded on a CF card in one operation.
Page Print Order Check the instractions for the device you are using, or with the photo printing service. Just insert the CF card into the printer for easy printing. You can select images one at a time, or select all images. For movies, only the functions in bold above can be set. Regarding images not taken with the EOS 60D, selectable functions may be limited.
Then you can playback the captured movies and photos on the TV. You can also playback the photos and movies recorded in the card as an automatic slide show. Select a movie. On the index display, the perforation on the left edge of the image indicates that it is a movie.
Slow motion The slow-motion speed is indicated on the upper right. On the movie playback screen, select [X]. The editing screen will be displayed. Specify the part to be edited out. Select [Slide show]. Select the images to be played. Display time Repeat Transition effect Start the slide show. Before connecting or disconnecting the cable between the camera and television, turn off the camera and television. The image will appear on the TV screen.
Select [Protect images]. The protect setting screen will appear. Select the image and protect it. When the [3 Protect images] menu option is set to [All images in folder] or [All images on card], all the images in the folder or card will be protected. Protected images p. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them.
The images will be displayed. Select the images to be erased. Select [LCD brightness]. Adjust the brightness. The setting of this feature can be changed. Select [Auto rotate].
It may not be possible to process images shot with a camera other than the EOS 60D. Post-processing images as described in this chapter cannot be done while the camera is connected to a personal computer Creative filters cannot be applied to 41 and 61 images. Select [Creative filters]. Page Creative Filters Save the image. Select [OK] to save the image.
Note the destination folder and image file number, then select [OK]. To apply a filter to another image, repeat steps 2 to 5. Page S Resize S Resize You can resize an image to make the pixel count lower and save it as a new image. Select [Resize]. The image size according to aspect ratios is shown in the table below.
Save the image. White balance p. Peripheral illumination correction p. If [Enable] is set, the corrected image will be displayed.
The image periphery will also be slightly cropped. Page Sensor Cleaning In case visible spots still remain after the automatic sensor cleaning, having the sensor cleaned by a Canon Service Center is recommended.
Even while the Self Cleaning Sensor Unit is operating, you can press the shutter button halfway to interrupt the cleaning and start shooting immediately. Normally, you need not pay attention to this operation. However, in case vis ble dust still remains, you can append the Dust Delete Data to the image for erasing the dust spots later. At a distance of 20 cm - 30 cm 0.
Page Manual Sensor Cleaning The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. Before cleaning the sensor, detach the lens from the camera.
Page Never use canned air or gas to clean the sensor. The blowing force can damage the sensor or the spray gas can freeze on the sensor. If a smudge that cannot be removed with a blower remains, having he sensor cleaned by a Canon Service Center is recommended.
Set up the printer. Page Preparing to Print Playback the image. Movies cannot be printed. Page Wprinting wPrinting The screen display and setting options will differ depending on the printer. Some settings might not be available. Printer-connected icon Select the image to be printed. The paper type screen will appear. The page layout screen will appear.
Set as necessary. If you need not set any printing effects, go to step 5. What is displayed on the screen differs depending on the printer. Page Start Printing wPrinting Set the date and file number imprinting.
Set the number of copies. Page wPrinting e Adjustment of Printing Effects In step 4 on page , select the printing effect. You can then adjust the printing effect. What can be adjusted or what is displayed will depend on the selection made in step 4. Page Trimming The Image wPrinting Trimming the Image You can crop the image and print only Tilt correction the trimmed portion as if the image was recomposed. Do the trimming right before printing.
If you set the trimming and then set the print settings, you may have to set the trimming again. Page wPrinting Depending on the printer, the trimmed image area might not be printed as you specified. The smaller you make the trimming frame, he grainier the picture will look in the print. If you look at the image on a TV screen, the trimming frame might not be displayed accurately.
The print settings will be applied to all print-ordered images. They cannot be set individually for each image. Setting the Printing Options Select [Print order]. Index Multiple thumbnail images are printed on one sheet.
Print type Both Prints both the standard and index prints. Date [On] imprints the recorded date on the print. File number [On] imprints the file No. Image Select and order images one by one. Prepare to print. See page Under the [3] tab, select [Print order]. Select [Print]. The functions explained in this chapter will take effect only in the Creative Zone modes. Select the group. Select the Custom Function No.
Custom Function No. Fn II: Image Long exposure noise reduction p. Fn I: Exposure C. Page C. Fn II: Image C. This [Auto] setting is effective in most cases.
The gradation between the grays and highlights becomes smoother. With setting 1, the Auto Lighting Optimizer p. Set this if the AF points lighting up is too distracting. The AF point will still light up when you select it. Fn III -5 Mirror lockup 0: Disable 1: Enable Prevents camera v brations caused by the reflex mirror action that can disturb shooting with super telephoto lenses or close-up macro shooting. See page for the mirror lockup procedure.
Page Even if you clear all the Custom Function settings to the default settings, the C. Fn IV -4 setting will be retained. Fn IV is set upon factory shipment.
To change the focusing screen, refer to the instructions that come with the focusing screen. Fn IV -5 Add image verification data 0: Disable 1: Enable Data for verifying whether the image is original or not is appended to the image automatically.
When the shooting information of an image appended with the verification data is displayed p. Select [My Menu settings]. Select [Register to My Menu]. Set the camera. Page Reference Reference This chapter provides reference information for camera features, system accessories, etc. Under the [7] tab, the [INFO. To register multiple battery packs to the camera, do the procedure below for each battery pack. With the battery info.
Write the serial No. Serial No. Page 3 Checking the Battery Information Checking the Remaining Capacity of a Registered Battery Pack You can check the remaining capacity of any battery pack even while not installed and also when it was last used.
Look for the serial No. The image transfer is a function of the Eye-Fi card. Select [Connection info. Turn he camera off and on again. Even if [Eye-Fi trans. In hospitals, airports, and other places where wireless transmissions are prohibited, remove the Eye-Fi card from the camera.
Fn I : Exposure C. Fn II : Image C. If there is a problem wi h he battery charger or battery pack or if When the image recording is completed, the power will turn off automatically.
Page Troubleshooting Guide The card cannot be used. If a card error message is displayed, see page 33 or The image is out of focus. To prevent camera shake, press the shutter button gently p. Page Set [8C. Fn I Flash sync. The external flash does not fire. If you use a non-Canon flash with Live View shooting, set the [z Silent shoot. The camera makes a noise when it is shaken. If you use flash, the shutter will make two sounds each time you shoot p. On the Quick Control screen, check the [Custom Controls] setting p.
Page Troubleshooting Guide When the movie is played, camera operation noise can be heard. Use an external microphone commercially available p. Set the color space to sRGB. If Adobe RGB is set, the first character will be an underscore p. The file numbering does not start from If you use a card which already has images recorded, the file numbering might start from the last image in the card p.
Page Troubleshooting Guide [ ] is displayed. The [Eye-Fi settings] menu item does not appear. This manual is also suitable for: b b b Print page 1 Print document pages. Rename the bookmark. Delete bookmark? Cancel Delete.
Delete from my manuals? Sign In OR. Therefore, if you are trying to master a certain product, going further on its manual will be the best choice to take. We understand that this camera is not a new product by Japanese camera manufacturer, Canon. With this manual, we hope it can be helpful for you in understanding this product. And if you want to know more about this specification, Overall look will be the best thing to start the topic.
This product is produced as digital single lens reflex or well known as DSLR. With such a delighted taste of style, it will be such a pride of having stylish digital camera product since you can show it everywhere and every time. EOS-D60 fulfill that requirement by its x x 75 mm or about 6.
Moreover, it is supported by light weight of the overall item, approximately grams. The 1. It shows satisfying reviews by its TFT liquid-crystal monitor technology. Besides, you are allowed to use eye-level pentaprism viewfinder hardware on the upper side of the product. With 6. The lens is interchangeable, so you are able to select the most suitable lens based on your needs.
To detect object precisely, CMOS
0コメント