Free shipping Free shipping Free shipping. Seller Last one Last one Last one. Report item - opens in a new window or tab. Seller assumes all responsibility for this listing. Item specifics. Seller Notes:. Time Period Manufactured:. Shipping and handling. The seller has not specified a shipping method to Germany. Contact the seller - opens in a new window or tab and request shipping to your location. Shipping cost cannot be calculated.
Please enter a valid ZIP Code. Shipping to: United States. No additional import charges at delivery! This item will be shipped through the Global Shipping Program and includes international tracking. Learn more - opens in a new window or tab. There are 42 items available. Please enter a number less than or equal to Select a valid country. Please enter 5 or 9 numbers for the ZIP Code. Handling time. Taxes may be applicable at checkout. Learn more.
Return policy. Return policy details. Seller does not accept returns. Refer to eBay Return policy for more details. You are covered by the eBay Money Back Guarantee if you receive an item that is not as described in the listing.
Payment details. Hold the bobbin between the thumb and forefinger of the right hand, the thread leading on top from the left toward the right see Fig. Then pull the thread into the slot in the edge of the bobbin case see Fig.
After threading, take the bobbin case by the latch, holding it between the thumb and forefinger of the left hand. Place the bobbin case on the centre stud 1, Fig. Allow the thread to hang free and close the slide in the bed of the machine. Turn the balance wheel over toward you until the needle bar 9, Fig. Turn the balance wheel over tow toward you until the thread take-up lever 5 is raised to its highest point. Place the spool of thread on the spool pin at the top of the machine, lead the thread toward the left through the thread guide 1 at the back and at the top of the face plate, down, under and from back to front between the tension discs 2 up back of the tension thread guard 3 , down into the loop of the takeup spring 4 , up and from back to front through the hole in the end of the thread take-up lever 5 , down into the eyelet 6 in front of the face plate, into the lower wire guide 7 , then from left to right through the eye of the.
Draw about two inches of thread through the eye of the needle with which to corn commence sewing. Welcome to ManualMachine.
We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Sewing Machine No.
Table of Contents Next Page. Previous Page Next Page. Skipping of Stitches. See that the needle is not bent, the upper See that the needle is correctly set see page tension is not too tight, and the presser foot 5 , is not blunt, bent, or too fine for the or attachments are securely fastened. This may be done by placing the bias gauge upon the point of the scissors and setting the blued indicator to the width desired.
Place the edge of the material to be bound between the scroll of the binder and under the needle, lower the presser-bar lifter and sew as usual. If the material is allowed to slip away from the scroll when near the needle, the edge will not be caught in the binding. The edge to be bound must be allowed to pass freely through the scroll and should not be crowded in or against it. Guiding should be from the back of the binder and to the left, allowing unfinished edges to swing naturally into the scroll of the binder.
When binding an inside curve, straighten out the edge as it is being fed into the Binder. When doing this, take care not to stretch the edge of the material. Slide the wire into its holder on the foot, and set it to the width desired; Then, with the hemmer foot raised, place the material from left to right under the foot and, with its edge slightly raised, insert the corner into the mouth of the hemmer, easing it along until it fills the curl and reaches the needle.
Raise the hemmer to relieve the pressure on the hem, and pass the end of the lace through the slot in the side of the attachment and over the hem, as shown. Loosen the screw at the front and move the slide until the pointer is against the desired width then tighten the screw.
Insert the edge of the material between the slide and the number gauge, and draw it backward and forward until the hem is formed, stopping with its end under the needle. Fold and crease down a hem of the desired width, pass the fold under the extension at the right of the hemmer, then insert the edge of the material into the folder, and proceed to sew. To attach the under braider, draw the front and back slides that cover the shuttle, and insert the downward projecting parts of the attachment against the edge of the throat plate.
Close first the back slide, then the front, so that the end of the front slide will enter the turned under part of the attachment and hold it firmly in position. This manual is also suitable for: No.
0コメント